Diesel Gas Cans
Diesel Gas Cans
 |
 Kerosene Jugs Can Gas Diesel Cans Storage  US $15.00
|
 5 Gallon Yellow Type I Safety Diesel Metal Gas Can US $49.99
|
Stress Analysis of a Natural Gas Engine Cylinder Head
1. Introduction
In the past, optimization of engine components such as cylinder heads was based on building a series of physical prototypes, and performing a series of different experiments and tests [1]. Unfortunately, the traditional process for designing and developing was time-consuming and difficult to build physical prototypes during the early stages of the design. The construction and testing of many prototypes is often required to meet a stringent design requirement [2]. This can turn into an expensive process and delay the entire design and development cycle. Although building and testing of the engine component prototypes can yield accurate design, detailed information is not available and the logic behind a specific design cannot be verified. As a result, engineers attain little and general information from each test [3]. Therefore, the finite element analysis (FEA) methodology is being used and becoming a systematic methodology in the early stages of engine design to save the time and cost of manufacturing process. Finite element analysis methodology (FEA) assist engineers to predict the best method for heat removal prior to the first prototype is built by calculating the temperature and stress distribution of each component. Therefore, finite element analysis (FEA) is considered as one of the most powerful computer-aided design tools for engineers [4]. In the process of an engineering analysis, a theoretical and numerical model is the starting point for researchers to develop or design an engineering system. This technique has been accepted for designing and developing complex geometry over a shorter period of time and at much lower cost.
The cylinder head is one of the most complicated and challenging parts of engine, where FEA plays an important role in its optimization [5]. A limited amount of information is available regarding thermal stresses in cylinder head. Komo and Bryzik investigated the development of thermal stresses in engine components with isolative ceramic coatings [6]. A twin-cam 16-valves cylinder head and cylinder block structure accompanied with several important subcomponents under firing load and assembly loads were investigated using FEM. The physical behavior of the gasket bead and liner, the stiffness distribution of cylinder head, the preload of the cylinder head bolts, the residual insertion loads of valve guides and valve seats, and firing pressure have been thoroughly discussed [7].
Other investigators carried out the sealing and structural response analyses under assembly and firing load cases for several areas of interest. Recommendations obtained from the project were forwarded to designers for successful incorporation into and adjustment of other areas for design evaluation. They provided information in regard to the nature and magnitude of thermal and mechanical stresses in the cylinder heads [8-10]. For calculation of boundary conditions from combustion chamber side, the model of the engine combustion was performed by commercial computer software [8-9, and 11-12]. The goals of the analysis were to provide: (1) Validation of the natural gas engine thermo-mechanical simulation results as are compared with the results of base diesel engine; (2) Achieving the thermal and mechanical stresses; (3) Comparison of the stress magnitude with the limits of elasticity [13-15].
2. Experimental Measurements
The engine specifications under the study are shown in Table 1. To apply accurate boundary conditions and input data to run the computational model, experiment was carried out to measure different parameters such as coolant flow rate, coolant inlet temperature, inlet air flow rate, inlet air pressure and temperature, exhaust gas flow rate, and outside cylinder head surface mean temperature (Table 2).
In this project, the engine performance data was measured by a dynamometer at 1850 RPM. The engine under investigation was equipped with six thermocouples. Three thermocouples were installed on the outside surface of cylinder and cylinder head to measure the average outside surface temperature. The inlet and outlet temperatures of the water jacket and the gas inlet port were measured using three thermocouples. The pressures at the inlet and outlet ports were measured using Piezo-Electric pressure transducers. The accuracy of temperature measurement were 0.1 C, pressure 0.001 KPa, and mass flow rate 0.1m3/s.
3. Computational Methodology
Details of the effort include model definition, meshing, model analysis, validation of the Finite Element Analysis (FEA) model, and applying thermal stress, and displacement boundary conditions. The results of the stress analysis, stress field in the firedeck, and the material evaluation are provided. The analysis procedure is shown in figure 1. The first stage in the process is to define the model geometry. This was accomplished using three-dimensional solid modeling using a computer-aided engineering tool, Solid Works [11]. The data is imported from the solid model to the mesh generation software. Mechanical boundary conditions and model constraints are defined and/or calculated to maximize the validity of the analysis given for the model [10]. Thermal and mechanical boundary conditions are applied to the finite element mode. The finite element analysis was carried out using a commercial finite element analysis software package, ANSYS [12]. The results are post processed into a form suitable for engineering assessment that accesses the analysis code's binary database and extracts appropriate results [13]. Local properties may be a function of surface finish, heat treatment, notch sensitivity, temperature, etc., and are an input by the user. Where the temperature dependency exists, user-input tables of temperature dependency calculate the local material property [14, 15]. The numerical analysis to calculate the temperature and stress distribution in cylinder head is achieved by multi-field technique. The essence of multi-field analysis is coupled-field analysis, which allows users to determine the combined effects of multiple physical phenomena (fields) of a design. If the input of one field analysis depends on the results of another analysis, the analyses are called multi-field. The applications of this technique include fluid-thermal and thermal-structure analysis. The computation processes for the analysis are shown in Figs 2 and 3.
3.1. Model Definition and Mesh Generation
The cylinder head model and its geometry are shown in Figure 4. The three dimensional solid modeling was performed by SOLIDWORKS [11]. The cylinder head mesh is constructed with ANSYS.
For thermo-hydraulic analysis, a model of the water jacket (Fig. 5) that receives local velocity and temperature of the cooling water was constructed. Flow characteristics of the water jacket, critical for keeping uniform firedeck cooling were analyzed using ANSYS. Also, brick-element mesh was constructed for water jacket with ANSYS. The combustion chamber is modeled by a computer software package, MATLAB, which calculate the gas temperature and pressure at each crank angle. The calculation is based on single zone model. For detail, see references [3, 16].
In any computational analysis, accurate mesh generation plays an important role. Therfore, sensitive areas are meshed with high resolution. The shape at the valve opening tapers outward near the firedeck, giving the valve bridge a smaller cross-section than any other location in the cylinder head. The valve bridge area is a region of concern and is finely meshed to determine accurately stress gradients as recommended by many investigators [4]. The completed three-dimensional model contains 507533 elements and 50965 nodes to model the cylinder head, and 733252 elements and 91244 nodes to model the water jacket. Element aspect ratios are chosen to be approximately 2.8 in the valve bridge area (Fig. 6). Away from the valve area, element aspect ratio less than 6.0 is used. However, this was not considered to be a significant problem because the stress gradients at these locations are very low. In the non-sensitive regions such as the top of the cylinder head, a coarse mesh is applied in order to reduce the number of elements and CPU time. The water jacket model of the cylinder head is meshed until the nodes of the interface of the cylinder head and water jacket models merge together. The results (along the x direction and across the y direction) indicate that the constructed finite element meshes with 7 x 3 elements in the bridge area would model the thermal process quite adequately. The thermal results of the finite element model that was constructed with this mesh criterion were compared with a highly refined mesh (two times refinement). The difference in results was considered acceptable (within 0.5 percent) for our study. In this analysis, it was found that the mesh types play an important role. Therefore, different types of meshes were examined until the mesh independency solution was achieved.
3.2. Thermal Boundary Conditions
In any thermal analysis, selection of proper boundary conditions is challenging, particularly for engine combustion chamber components, where boundary conditions may vary significantly both in space and time [16, 17]. The boundary conditions for stress analysis combine the results from the thermal analysis and displacement boundary conditions suitable for the cylinder head. In this analysis, only thermal and pressure loads from the combustion chamber were considered. This is not a serious limitation as thermal stress is the dominant form of stress in the cylinder head [18]. In this work, the regions of high stress were sought rather than a particular highly accurate stress value. To satisfy the thermal boundary conditions, the convective heat transfer coefficient should be calculated for all the following regions.
3.2.1 Outside Boundary Condition
To apply outside boundary conditions, the Rayleigh equation (1) is used for a free convection surface [17].
(1)
The value of is 0.25 and is 0.52
The Rayleigh and Grashoff numbers are calculated by the following equations,
(2)
(3)
3.2.2 Inlet and Outlet Ports Boundary Condition
To calculate the thermal heat transfer coefficient in the intake and exhaust ports, Christopher equation is used [19]:
(4)
Where,
(5)
The value of is acquired from CFD or experiment. Air temperature in this turbocharged engine at the inlet port is 337.1 K, and the gas temperature at the outlet port is assumed to be the same as the combustion chamber gas temperature when the exhaust valve is opened. It was calculated as follow [20]:
(6)
3.2.2 Water Jacket Side Boundary Condition
The prediction of the temperature distributions is achieved by solving the energy, momentum, and mass conservation equations simultaneously. Therefore, the water jacket inlet pressure and/or velocity are required to apply as boundary condition in the CFD model. For this purpose, the inlet water flow rate and temperature are measured. [21, 22].
3.2.3 Combustion Chamber Boundary Condition
To calculate the thermal heat transfer coefficient in the combustion chamber, the Woschni equation (7) is employed. To use this equation, pressure and temperature should be calculated at each crank angle.
(7)
In this equation b is the cylinder bore, is the average of gas velocity, which is almost equal to average of piston velocity. Figure 7 shows the gas pressure and temperature profiles in the combustion chamber
3.3. Stress Boundary Conditions
In order to reduce the complexity of the boundary conditions for stress analysis, the interaction between the cylinder head, cylinder head gasket, and cylinder block was not modeled. In fact, the cylinder head and the cylinder block were assumed to expand at the same rate for all points of contact between the cylinder block and cylinder head. This simplification does not allow the cylinder head bolts to constrain the thermal expansion of the cylinder head. Therefore, the thermal stresses are expected to be under-predicted. The other boundary condition is the pressure load that is applied to the combustion chamber. The maximum pressure of 10.5 (MPa) is used in this analysis. The boundary condition of the bolt is very significant since a pre-load is necessary to define tightening of the bolt. In this analysis, it is assumed that the surface interface of the cylinder head and bolt is moved inward. There is no outward movement for this surface. Therefore, for modeling, the contact element between the bolt and cylinder head is used [14].
4. Results and Discussion
As explained before, the first step in the analysis is to validate the computational model. The comparison of experimental and computational results is shown in Fig. 8. Nodes 1—8 in this figure are corresponding points to the numbers 1—8 in Fig.9. The calculation is performed for one temperature cycle at high coolant temperature. It is evident that a very good correlation exists between measured and calculated strains for lower temperatures where elastic material behavior predominates. For the higher wall temperatures exceeding 200 C, the calculation overestimates the influence of inelastic material deformation as compared with the measured values.
It is concluded (Fig. 
that the Van Mises stress results are matched relativity very well. Therefore, the model can represent the baseline engine cylinder head and it can be further used for parametric studies.
The comparison of Diesel and Natural Gas Engines stress analysis results is shown in Figure 10. The results of Von Mises stress for Natural Gas Engine in cylinder 2 are 1.12 times more than corresponding points in the diesel engine. This is due to higher temperature of Natural Gas.Thermal and structural analysis results show the temperature and Von Mises distribution in cylinder 2 are higher than the others. So, our discussion is concentrated on cylinder 2. It is assumed that the temperature in the water jacket is constant. Figs.11 and 12 show that the temperature at the cylinder bridge is high in both engines; and consequently the temperature gradient at this region remains high. It is also concluded that the temperature distributions are different in all cylinders since the cooling water enters the left side of the bottom end of the block and exits from the left side of the top end of the cylinder head. Therefore, cylinder 1 is cooler than the others and the temperature gradient in cylinder 2 is higher than the other cylinders. Also, the highest temperature at the centre of any cylinder decreases away from the centre. This causes a high temperature gradient at the surface of the combustion chamber. This is due to the fact that far away from the centre, the cooling water flow rate is larger than at the centre of the firedeck. The results predict a large compressive strain and stress field at the valve bridge and seats on the firedeck of the cylinder head. These stresses are primarily due to relatively large temperature difference existing at the liner interface. The maximum temperature at firedeck is 616 K in Natural Gas and 549 K in Diesel engine. The results show that the temperature gradient at the gas side of the cylinder head of the natural gas engine is approximately 53 ºC/mm, and it is 5.6 ºC/mm for the coolant side of the cylinder head. Inside the liner, the temperatures on the firedeck change from 438 K to 616 K at high load operating conditions, while outside of the liner, the temperatures are relatively low at 293 K to 360 K.
The thermal expansion of the hot region is constrained by the stiffer cool region, which undergoes less thermal expansion. As a result, a compressive thermal stress field is created inside the liner. Figure 13 shows the temperature distribution contours of the cylinder head. The maximum stress on the cylinder head also showed similar results. In this work, first, the maximum cylinder gas pressure is applied to cylinder 2, then to the other cylinders. It is concluded that the average stress in the cylinder head reached its maximum value when the cylinder head 2 is under fire. When cylinders 1, 3, and 4 are under fire, the maximum stress is observed in cylinder 2 because the temperature gradient in cylinder 2 is more than in the other cylinders. Also, higher stress in the valve bridge and near the valve seat is seen in Figs.14 and 15 because the thickness of material in the valve bridge is higher and cooling flow rate is lower. Figures14, 15, 16, and 17 show larger compressive strain and stress at the valve bridge and seats on the firedeck of the cylinder head. An important observation from the result of the analysis is that the predicted Von Mises stresses exceed the limit of elasticity (dark areas in Fig. 18) for a typical cylinder head material [25]. This high stress would lead quickly to destruction of the cylinder head.
5. Conclusion
The maximum compressive stress is observed in the valve seats and valve bridge. Natural Gas engine stress is about 1.12 times higher than Diesel engine. High stresses at the valve bridge resulting from a constrained thermal expansion of the cylinder head are generally compressive. It is concluded that about 82%–87% of the total stress is thermal and the rest is due to pressure and mechanical stresses.
The temperature gradient at the surface of combustion chamber is not uniform. The maximum total stress was found in cylinder 2. The Von Mises stress value of the Natural Gas engine exceeded the elasticity limit of material used for the cylinder head. This high stress would lead to destruction of the cylinder head. It is recommended modifying the current cylinder head material from cast iron GG-26 to GG-30 in order to prevent failure of cylinder head. The engine cooling system should also be improved to reduce the area with maximum compressive stress.
REFERENCES
[1]. Spaniel, M., Macek, J., Divis, M., Tichanek, R., "Diesel engine head steady state analysis", Research Report of Technical University in Prague, 2003.
[2]. Assanis, N., "Multi-Dimensional modeling of Natural gas ignition under compression ignition conditions using detailed chemistry", SAE paper 980136, 1998.
[3]. Bryzik, W., Wood, M., Schwarz, E., and Glance, P., "High temperature engine component exploratory design development", SAE paper 890296, 1989.
[4]. Tichanek, R., Spaniel, M., Divis, M., "Steady state heat analysis of engine head", Research Report of Technical University in Prague, 2002.
[5]. Woods, M., Schwarz, E., and Bryzik, W. "Advances in high temperature components for the adiabatic engine", SAE paper 910460, 1991.
[6]. Komo, R., Bryzik, W., "Performance and durability of a ceramic coated adiabatic engine", ASME ETCC Symposium, New Orleans, LA, January, 1990.
[7]. Chyuan, S., "Finite element simulation of a twin-cam 16-valve cylinder structure", Finite Element in analysis and Design, Elsevier Science Publishers B. V., Amsterdam, Netherlands, 2000.
[8]. Roelle, M. J., Shaver, G. M., Gerdes, J. C., "A multi-mode combustion model of SI and HCCI for mode transition control", international mechanical engineering conference and exposition Anaheim, California, USA, November 13-19, 2004.
[9]. Cranfield, A., "Effects of diesel water emulsion combustion on diesel engine NOx emissions", MS Thesis of Florida university, 1999.
[10]. Trigui, N., Griaznov, V., Affes, H., Smith, D., "CFD based shape optimization of IC engine", J. of Oil & Gas science and Technology, Vol. 54, pp.297-307, 1999.
[11]. Reyes, A., "Beginner's guide to Solidworks", Schroff Development Corporation (SDC) Publications, India, 2005.
[12]. Lawrence, K., "Ansys workbench tutorial", Schroff Development Corporation (SDC) Publications, India, 2005.
[13]. Segerlind, L. J., "Applied finite element analysis", 2nd Edition, John Wiley, 1984.
[14]. Jorwekar, P., Birari, V., Nadgouda, M., "Cylinder head gasket contact pressure simulation for a hermetic compressor", International compressor engineering conference, Purdue, July 17-20, 2006.
[15]. Catania, A. E., Misul, D., Mittica, A., Spessa, E., "A refined two-zone heat release model for combustion analysis in SI engines", The 5th international symposium on modeling of Combustion in IC Engines, Comodia, 2001.
[16]. Ferguson, C. R., "Internal Combustion Engine", John Wiley, New York, 1986.
[17]. Wendl, M. C., "Fundamentals of heat transfer theory and applications", Class notes for ME 371 of Washington University, Version 2.1, 2005.
[18]. Tatschl, R., Basara, B., Schneider, J., Hanjalic, K., Popovac, M., Brohmer, A., Mehring, J., "Advanced turbulent heat transfer modeling for IC-Engine applications using AVL fire", Research report of international multidimensional engine modeling, Detroit MI, April 2, 2006.
[19]. Christopher D., Dennis A., "A universal heat transfer correlation for intake and exhaust flows in a spark-ignition internal combustion engine", SAE paper 2002-01-0372, 2002.
[20]. Pulkrabek, W., "Engineering Fundamentals of Internal Combustion Engine", Prentice Hall, 2nd Edition, 1997.
[21]. Chang, J., Guralp, O., Filipi, Z., Assanis, D., Kuo, T.W., Najt, P., Rask, R., "New heat transfer correlation for an HCCI engine derived from measurements of instantaneous surface heat flux", SAE paper 2004-01-2996, 2004.
[22]. Taylor, C. F., "The internal combustion engine in theory and practice", MIT Press, 2nd Edition, 1966.
[23]. Woschni, G. A., "A universally applicable equation for the instantaneous heat transfer coefficient in the internal combustion engine", SAE paper 670931, 1967.
[24]. Pischinger, S., "Internal combustion engine", VKA paper, institute for internal combustion engine, 2007.
[25]. Germany Industrial Norm, "Material standard DIN paper 1691", 1985.
Nomenclature
Area (m2)
Cylinder bore (m)
Average diameter of inlet and outlet ports (m)
Acceleration of gravity (m/s2)
Grashoff number
Convective heat transfer coefficient (w/m2K)
Thermal conductivity coefficient (w/mK)
Mass flow rate (kg/s)
Nusselt number
Gas pressure (pa)
Intake cylinder pressure (pa)
Exhaust gas pressure (pa)
Prandtl number
Rayleigh number
Reynolds number
Temperature (K)
Exhaust gas temperature (K)
Ambient temperature (K)
Gas velocity (m/s)
Displacement volume
Greece Symbols
Coefficient of volumetric thermal expansion (k-1)
Dynamic viscosity (kg/ms)
Kinematic viscosity (m2/s)
CAPTURES
Table 1. Engine specifications
Table 2. Natural gas engine experimental data to be used for computational modeling
Figure 1. Thermo-mechanical analysis procedure
Figure 2. Multi-field computations procedure for CFD-Thermal a: formulation b: loops sequence
Figure 3. Multi-field computations procedure for Thermal-Structural
Figure 4. Model of the engine cylinder head
Figure 5. Model of the water jacket for CFD analysis
Figure 6. Top view of nodes distribution in combustion chamber of the cylinder head.
Figure7. Pressures and temperature profiles in Natural gas and diesel engines.
Figure 8. Comparison of the experimental and computational stress results, node numbers
correspond to the points on the cylinder head in Fig. 9
Figure 9. Location of measured and computed stress in the cylinder head
Figure 10. Comparison of Von Mises stress distribution on fire-deck of combustion surface of Natural gas and Diesel engine cylinder head
Figure 11. Temperature contours on the firedeck of the combustion surface of Natural gas engine (K)
Figure 12. Temperature contours on the firedeck of the combustion surface of Diesel engine (K)
Figure 13. Temperature distribution contours on the firedeck combustion surface (K) of Natural gas engine
Figure 14. Von Mises stress contours on the firedeck combustion surface of Natural gas engine (MPa)
Figure 15. Von Mises stress contours on the firedeck combustion surface of Diesel engine ( MPa)
Figure 16. Von Mises strain contours on the firedeck combustion surface of Natural gas engine
Figure 17. Von Mises strain contours on the firedeck combustion surface of Diesel engine
Figure 18. Von Mises stress on the firedeck combustion surface more than yield stress
No. of Cylinder
4
Max Power
81 KW @ 2800
Max Torque
350 N.M @ 1600-2100 RPM
Compression Ratio
11:1
Cylinder Bore
97 mm
Stroke
128 mm
Volume
3780 cm3
Cooling Water Capacity
8 Liter
Fuel
Natural Gas
Air Induction System
Turbocharged and Intercooler
Fueling Strategy
Lean Burn
Table 1
Parameters
Measured
Coolant flow rate (m3/h)
Coolant inlet temperature ( K)
Coolant outlet temperature (K)
Inlet air flow rate per cylinder (kg/h)
Inlet air temperature ( K)
Exhaust flow rate per cylinder (kg/h)
Fuel flow rate per cylinder (kg/h)
Cylinder head mean temperature of the outside surfaces of ( K)
Inlet air pressure (KPa)
Table 2
Authors:
Abolfazl Vafadar Yengjeh and Hassan Vafadar Yengjeh
Mechanical Engineering Tehran, Iran
About the Author
Abolfazl Vafadar Yengjeh and Hassan Vafadar Yengjeh
Mechanical Engineering Tehran, Iran
|
|
Compressed Gas Duster, 10 oz. Cans 2 Cans Per Case.10 oz. Per Can. $7.26 Manufacturer: Innovera. Pack of 2 Cans. Customers also search for: Compressed Gas Duster;Duster;Gas;INNOVERA, 686024515050 |
|
|
Diesel Fuel $92.4 Diesel fuel. Diesel engine, Gasoline and diesel usage and pricing, Synthetic fuel, Biodiesel, Dieselisation, Diesel locomotive, Aircraft diesel engine, Exhaust gas, Diesel particulate matter, Diesel exhaust air contaminants Author: Miller, Frederic P./ Vandome, Agnes F./ McBrewster, John Binding Type: Paperback Number of Pages: 118 Publication Date: 2009/10/11 Language: English Dimensions: 5.98 x 9.01 x 0.27 inches |
|
|
DAV2002 Six Shooter Fuel Pump, Gas & Diesel $15.95 DAV2002 Six Shooter Fuel Pump, Gas & Diesel Type: Replacement Parts Color: Multi-Color Gender: Unisex Age: Adult |
|
|
Diesel 2 Diesel Sweatshirt by CafePress $39.5 Diesel Gas Pump created for our fave DieselDykes; but perfect for truckers, big rigs, boaters, dualies, gas stations, mechanics; anyone, any machine or engine that handles, uses or stores Diesel fuel. Diesel Sweatshirt Tee, TShirt, Shirt Warm up in our stylin' Hanes Heavyweight 90/10 cotton/polyester sweatshirt. Thick but not bulky, for maximum comfort and durability whether you're working out or hanging out. 10.1 oz. patented PrintPro174; fabric in a 90/10 cotton/polyester |
|
|
Universal Compressed Gas Dusters, 10 oz. Cans, 2 Cans per Pack. Pack of 2 $8.84 Manufacturer: Universal Office Products. Pack of 2. Compressed Gas Dusters Blasts away dust and dirt from computers, printers, copiers and more. 100% ozone safe; no CFCs, HCFCs, butane or propane. 2 Cans per Pack 10-oz. Cans Customers also search for: 10- |
|
|
No Spill Llc No Spill Llc 5gal Diesel Can 1457 $28.22 5gal diesel can Professional quality No Spill gas cans are tested and certified to meet standards and specifications for portable gasoline containers for consumer use Utilizes patented self-venting, self-sealing nozzle; just pick up, tip, and press the button to pour Flows up to 3 gallon per minute No spill push-button nozzle stops flow automatically when the tank reaches full The tapered 7/8? o.d. spout has a 20 mesh stainless steel screen in the spout to filter out debris while pouring Attached dust cap protects spout from dust and debris when not pouring Flex spout attachment, sold separately, allows filling of on-road vehicles, boats, and many other hard-to-reach tank openings CARB and EPA compliant Brand #: No Spill LLC 1457 UPC: 759176014570 Keywords: professional gas can carb compliant epa no spill fuel 5 gal diesel gallon |
|
|
Gas/Water Can Holder by Garvin Industries for Jeep $111.99 1984-01 Jeep XJ Cherokee;part number 34800 rear bumper;Black powder coat;Accepts Blitz, Wedco and Sceptor 5 gallon cans JEEP CHEROKEE (XJ) BRIARWOOD CHIEF CLASSIC COUNTRY LAREDO LIMITED PIONEER SE SPORT 1984 1985 1986 1987 1988 1989 1990 1991 1992 1993 1994 1995 1996 1997 1998 1999 2000 2001 2.1L Turbocharge Diesel (126) 2.5L (150) 2.8L (173) 4L (242) 4L Power Tech (242) DIESEL GAS Gas/Water Can Holder by Garvin Industries for Jeep |
|
|
Diesel 2 Diesel White T-Shirt by CafePress $22 Diesel Gas Pump created for our fave DieselDykes; but perfect for truckers, big rigs, boaters, dualies, gas stations, mechanics; anyone, any machine or engine that handles, uses or stores Diesel fuel. Diesel White T-Shirt Tee, TShirt, Shirt The white t-shirt is a timeless classic for a reason; it should be a staple in every wardrobe. It is clean, simple, and durable. The best part is you can wear it with anything. This 100% cotton T-shirt is so comfortable you'll want to wear it to bed. |
|
|
Diesel 2 Diesel Light T-Shirt by CafePress $22 Diesel Gas Pump created for our fave DieselDykes; but perfect for truckers, big rigs, boaters, dualies, gas stations, mechanics; anyone, any machine or engine that handles, uses or stores Diesel fuel. Diesel Light T-Shirt Tee, TShirt, Shirt This light t-shirt will be fashionable even after the zombie Apocalypse. In fact, this shirt might be the very reason you'll survive said Apocalypse. The light color shows you aren't worried about getting stains - and even if you were, those stains show t |
|
|
Beatnik Cafe, the Gas House: Tex Kleen Reads Poetry in Tub as Fowad Magdalani Decorates Cans $79.99 Allan Grant Beatnik Cafe, the Gas House: Tex Kleen Reads Poetry in Tub as Fowad Magdalani Decorates Cans - Premium Photographic Print |
|
|
Falcon Safety Disposable Compressed Gas Duster, 10 oz. Cans, 2/Pack. Pack of 2 $22.38 Manufacturer: Falcon Safety. Pack of 2. Dust-Off Disposable Compressed Gas Duster Blows away harmful dust and lint. 100% ozone safe; no CFCs, HCFCs, butane or propane. Trigger controls spray power. Slip-on extender. 2 Cans per Pack 10-oz. Cans Customers a |
|
|
Bd Diesel Exhaust Thermocoupler Probe Kit 1081151 $85.99 Optional exhaust gas tempature thermocouple for BD Diesel Cool Down Timer kit |
|
|
Pounder's Marine Diesel Engines and Gas Turbines $160 Since its first appearance in 1950, Pounder's Marine Diesel Engines has served seagoing engineers, students of the Certificates of Competency examinations and the marine engineering industry throughout the world. Each new edition has noted the changes in engine design and the influence of new technology and economic needs on the marine diesel engine. Now in its ninth edition, Pounder's retains the directness of approach and attention to essential detail that characterized its predecessors. There are new chapters on monitoring control and HiMSEN engines as well as information on developments in electronic-controlled fuel injection. It is fully updated to cover new legislation including that on emissions and provides details on enhancing overall efficiency and cutting CO2 emissions. After experience as a seagoing engineer with the British India Steam Navigation Company, Doug Woodyard held editorial positions with the Institution of Mechanical Engineers and the Institute of Marine Engineers. He subsequently edited The Motor Ship journal for eight years before becoming a freelance editor specializing in shipping, shipbuilding and marine engineering. He is currently technical editor of Marine Propulsion and Auxiliary Machinery, a contributing editor to Speed at Sea, Shipping World and Shipbuilder and a technical press consultant to Rolls-Royce Commercial Marine. * Helps engineers to understand the latest changes to marine diesel engineers * Careful organisation of the new edition enables readers to access the information they require * Brand new chapters focus on monitoring control systems and HiMSEN engines. * Over 270 high quality, clearly labelled illustrations and figures to aid understanding and help engineers quickly identify what they need to know. |
|
|
Diesel 2 Diesel Women's Light T-Shirt by CafePress $22 Diesel Gas Pump created for our fave DieselDykes; but perfect for truckers, big rigs, boaters, dualies, gas stations, mechanics; anyone, any machine or engine that handles, uses or stores Diesel fuel. Diesel Women's Light T-Shirt Tee, TShirt, Shirt Our 100% cotton women's tee is preshrunk, durable and guaranteed.5.6 oz. 100% cotton. Standard fit. |
|
|
Diesel 2 Diesel Long Sleeve T-Shirt by CafePress $32.5 Diesel Gas Pump created for our fave DieselDykes; but perfect for truckers, big rigs, boaters, dualies, gas stations, mechanics; anyone, any machine or engine that handles, uses or stores Diesel fuel. Diesel Long Sleeve T-Shirt Tee, TShirt, Shirt The most comfortable t-shirt ever Our 100% cotton, Hanes Beefy-T is preshrunk, durable and guaranteed. 6.1 oz. 100% luxuriously soft ring spun cotton . Standard fit. Ribbed sleeve cuffs. |
|
|
Gas Can Carrier $57.62 Available for 2 or 5 gallon gas cans Handy for carrying other items as well **Note: Gas can and strap not included |
|
|
Gas, Oil, Diesel Fuel, Heating Oil DOT Placards $10.49 4-digit D.O.T. placards indicate specific hazardous materials. Each Placard includes a 4-digit UN number, corresponding hazard class graphic, and hazard classification number. Available in 4 materials - permanent vinyl, removable vinyl, semi-rigid plastic, or flexible magnetic. Hazardous material description: 1202 gas, oil, diesel fuel, heating oil. |
|
|
Handbook of Diesel Engines $269 Even today, the diesel engine remains the most economic internal combustion engine for vehicles, as well as for mobile and stationary machines. Also, when considering the issue of CO2 emission, the diesel engine holds a leading position in comparison to all other drive engines - especially when taking into account its flexibility, its capacity, overall emissions and robustness. To this English edition of the handbook, 58 eminent specialists have contributed.Compared with the previous edition, special emphasis is devoted to the subjects becoming more and more important, e.g. energy efficiency, exhaust-gas emission and aftercare, the fuel-injection process, electronic engine management as well, as conventional and alternative fuels. This unparalleled reference targets the specialist who is active in research and development or industrial practice, as well as students of mechanical engineering, mechatronics, electrical engineering and electronics who want to understand the function and the interaction within the complicated system comprising the diesel engine. |
|
|
Diesel 2 Diesel Jr. Jersey T-Shirt by CafePress $22.25 Diesel Gas Pump created for our fave DieselDykes; but perfect for truckers, big rigs, boaters, dualies, gas stations, mechanics; anyone, any machine or engine that handles, uses or stores Diesel fuel. Diesel Jr. Jersey T-Shirt Tee, TShirt, Shirt Turn heads in this hot, hip, curve-hugging tee from American Apparel. Made of ultra-fine, ring-spun cotton, it gets softer with each washing. Lightweight for summer comfort or winter layering, it39;s a casual, effortless way to ensure you39;re stylin |
|
|
Krylon G.m. Alpine Green 1pt. 6 Cans $39.3 Manufacturer: Krylon. 6 Cans. Fast-drying, high performance acrylic enamels Withstands temperatures up to 500 F Exact matches to OEM standards Won't blister, flake, crack or peel Oil and gas resistant Color = G.M. Alpine Green Capacity Wt. = 11 oz Packin |
|
|
Krylon Ford Blue 1pt. 6 Cans $39.3 Manufacturer: Krylon. 6 Cans. Fast-drying, high performance acrylic enamels Withstands temperatures up to 500 F Exact matches to OEM standards Won't blister, flake, crack or peel Oil and gas resistant Color = Ford Blue Capacity Wt. = 11 oz Packing Type = |
|
|
Troubleshooting Marine Diesel Engines $21.95 This densely illustrated, hands-on guide to diesel engine maintenance, troubleshooting, and repair renders its subject more user-friendly than ever before. Finally, boatowners who grew up with gas engines can set aside their fears about tinkering with diesels, which are safer and increasingly more prevalent. As in other volumes in the International Marine Sailboat Library, every step of every procedure is illustrated, so that users can work from the illustrations alone. The troubleshooting charts in the second chapter--probably the most comprehensive ever published--are followed by system-specific chapters, allowing readers to quickly diagnose problems, then turn to the chapter with solutions. Diesel engine systems covered include: mechanical; oil; fresh- and raw-water cooling; low- and high-pressure fuel; exhaust; starting; charging; transmission and stern gear. |
|
|
RBP Diesel Performance 251483 - RBP Diesel Custom Truck Grille $690.99 2007-11 Jeep JK Wrangler, Rubicon and Unlimited;2 and 4-door models;Black;Attaches over factory grille JEEP WRANGLER (07-12JK) ISLANDER MOUNTAIN RUBICON SAHARA SPORT UNLIMITED ISLANDER UNLIMITED MOUNTAIN UNLIMITED RUBICON UNLIMITED SAHARA UNLIMITED SPORT UNLIMITED X X 2007 2008 2009 2010 2011 2012 3.6L (220) 3.8L (231) GAS RBP Diesel Performance 251483 - RBP Diesel Custom Truck Grille |
|
|
Bilingual Diesel Fuel No Smoking Sign $17.79 Bilingual diesel fuel no smoking signs ensure your message is understood. Designate certain areas to be smoke free due to flammable gas. Wording - DANGER DIESEL FUEL NO SMOKING NO OPEN FLAMES / PELIGRO COMBUSTIBLE DIESEL NO FUMAR NO ACERCAR FLAMAS ABIERTAS Color - Black / Red / White Header - Danger Language - English / Spanish Material - Aluminum, Steel, Plastic, Foam Adhesive, Adhesive Vinyl, Magnetic, Plastic 3-Way, Plastic 2-Way Size - 10" x 7", 14" x 10", 20" x 14" Lifetime Guarantee available with optional Duroshield Topcoat |
|
|
Radiator Specialty 15 Oz Instant Starting Fluid. 12 Cans $31.08 Manufacturer: Radiator Specialty. 12 Cans. Quickly starts gasoline and diesel engines without glow plugs Contains upper cylinder lubricants Color = White Ply = 1 Brand Name = Charmin Type = Bathroom System Format = Roll Customers also search for: Disco |
|
|
Radiator Specialty 15oz Thrust Starting Fluid 11-oz Net. 12 Cans $31.2 Manufacturer: Radiator Specialty. 12 Cans. Quick, smooth starting of all gasoline engines and diesel engines without glow plugs Capacity Volume = 11 oz Packing Type = Aerosol Can Brand Name = Instant Applications = Engine Type = Starting Fluid Customer |
|
|
CRC 16 Oz Jump Start Starting Fluid (12/case). 12 Cans $62.52 Manufacturer: CRC. 12 Cans. Assures fast, economical starts in extremely cold or humid climates Upper cylinder lubricant minimizes wear during cold starts Effective to -65 F For diesel and gasoline engines Container Size = 16 oz Packing Type = Aerosol Ca |
|
|
Gas and Water filter by Crown Automotive $26.99 1994-01 Jeep XJ Cherokee;1993-03 Grand Cherokee;With 2.5L and 3.1L diesel engines Gas and Water filter by Crown Automotive |
|
|
Pounder's Marine Diesel Engines $150 Since its first appearance in 1950, Pounder's Marine Diesel Engines has served seagoing engineers, students of the Certificates of Competency examinations and the marine engineering industry throughout the world. Each new edition has noted the changes in engine design and the influence of new technology and economic needs on the marine diesel engine. This eighth edition retains the directness of approach and attention to essential detail that characterized its predecessors. There are new chapters on monitoring control systems and governor systems, gas turbines and safety aspects of engine operation. Important developments such as the latest diesel-electric LNG carriers that will soon be in operation. After experience as a seagoing engineer with the British India Steam Navigation Company, Doug Woodyard held editorial positions with the Institution of Mechanical Engineers and the Institute of Marine Engineers. He subsequently edited The Motor Ship journal for eight years before becoming a freelance editor specializing in shipping, shipbuilding and marine engineering. He is currently technical editor of Seatrade, a contributing editor to Speed at Sea, Shipping World and Shipbuilder and a technical press consultant to Rolls-Royce Commercial Marine. * Designed to reflect the recent changes to SQA/Marine and Coastguard Agency Certificate of Competency exams. Careful organisation of the new edition enables readers to access the information they require * Brand new chapters focus on monitoring control systems and governor systems, gas turbines and safety aspects of engine operation * High quality, clearly labelled illustrations and figures |
|
|
Diesel Gas Pump Humor Dark T-Shirt by CafePress $26 Get pumped up - on diesel Humor Dark T-Shirt Tee, TShirt, Shirt Don't waste time deciding on which shirt to put on each morning. This dark shirt t-shirt will never go out of style and hides stains better too. This high-quality t-shirt is pre-shrunk and 100% cotton, which makes it both comfortable and durable. |
|
|
Cute Cans $6 Cute Cans |
|
|
Diesel $13.99 Men's 0.15 oz EDT Mini. Created in 1996 Diesel is described as a refined oriental woody fragrance. This masculine scent possesses a blend of pepper mandarin lemon ginger clove and musk. Diesel is recommended for evening use. |
|
|
51515 - Compressed Gas Duster, Nonflammable, 2 10Oz Cans/Pack $25.01 [IVR51515] HAZMAT UPC: 686024515159 UNSPC: 44102904 2 LB |